CSR
New Products

The development and manufacture of reproduction parts is an on going process at Clarke Spares. Factory drawings and build sheets are not available so in most cases (in order to produce parts) original items and the knowledge of how they are installed and used act as samples for the typical reverse engineering process. A number of individuals provided information and/or original parts so the production of many of the new items listed on this page could become a reality.

Many thanks go to the following British car enthusiasts who helped resurrect parts that have not been available for many years.

Jim Alcorn, John Beesley, Charles E. Bishop, Peter Bonthrone, Peter Brauen, Rich Chrysler, Jamie Coobatis, John Davies, Brian Drew, Maury Drummond, Jeff Fishel, Tim Flarety, Ken Grasing, Ray Holtzapple, Steve Johnson, Winfried Kohnle, Tom Kovacs, Kent Lambert, Mark Lambert, John Mangles, Lynn Martin, Bill Meade, George Merryweather, Roger Moment, Ron Neal, Inan Phillips, Jonathan Stein and James H. Taylor.

Photographs by Russ Airey

P1000996
Close Out Notice

TC-02 MGA Twin Cam Air Filter Canister. Exact reproductions of the later improved/beefed up canister. Supplied powder coated.
SOLD OUT

P1000983
New Items

Clips for MGC. Most position on bottom of car and secure cables/harness sections. Made to original standards and supplied zinc plated. BMC numbers referenced where known. Please note rubber buffers originally used with AHC 331 and AHC 332 not available at this time.

On left from top to bottom AHC 332 - 9 per veh. $2.75ea. / $22.00 for 9 AHC 331 - 1 per veh. $2.50ea. Elongated (dual type) - secures two 9/16" diameter cables. 9/32" hole. $1.75ea. Elongated (dual type) - secures two 7/16" diameter cables. 9/32" hole. $1.50ea. On right from top to bottom AHC 580 - 1 per veh. - for speedo. cable. $4.75ea. PCR 1207 - Single Loop Clip for 3/4" diameter cable. 7/32" hole. $1.00ea.

P1000827
New Items

AHC 865 - Clip to secure MGB defroster hoses. 2 per veh. Steel with zinc finish - $2.50ea.

P1000820
New Items

SP-35 Repair Plate for MGA striker pillar face plate. Up to 4 per veh. Steel.
$3.50ea.

P1000839
New Items

Seat Slide Rails (attach to floor) for MGA (top) and MGB (bottom) The MGA rails have been in production for many years. The MGB rails are new. Steel, plated. M48 - MGA $13.00ea. / $49.00 for 4. M171 - MGB $14.00ea. / $53.00 for 4. Seat rail pcs. also available. Not shown. SP-38 Wood Spacers with holes in black finish for MGB rails. Produced from 9 ply marine grade plywood. $7.00ea. / $25.00 for 4. RS-12-18 Replating (exchange) Service for original upper seat rails - MGA/MGB $13.00ea. / $49.00 for a set of 4 (2 with handle / 2 without). Contact us with questions.

P1000928
New Items

Elongated (dual style) Clips. Lucas style feature belled edge on loop, 5/16" radius on leg ends and are supplied with yellow zinc finish. A number of sizes are now available. $1.50 to $1.75 each.

P1000945
New Items

AHH 8897 Dual Clip secures 1/4" clutch pipe and 3/16" brake pipe in front of MGB (many model years) heater box. Steel, zinc finish. $1.95ea. CHR 0611 - BMC style Half Clip for 3/8" pipe/cable. With 9/32" hole. 5/8" wide. .95ea. also available for "T" series/typical pre-BMC veh. (not shown) 3/4" width with 3/8" leg radius. $1.60ea.

P1000967
New Items

P33 Fiberboard Stiffener - MGA spare tire cover to boot wall. Out of production for many years the stiffener is die stamped from original type material with all holes. $15.00 ea.

P1000972
New Items

SP-36 Stay Clip with Screw for MG-ZA/ZB rear door seal. BMC No. ADG 890 4 per veh. Steel, plated. $1.25ea. / $4.50 for 4.

P1000978
New Items

SP-37 Lift Bracket as used on late MGA battery ledge cover. Can be retrofitted to earlier covers. Steel, plain finish. 1 per veh. $3.75ea.

new parts
New Items

MGA Factory Hard Top Brackets and Fasteners All pcs. are available individually and in kit form. Made to original standards except the rear “teardrop” shaped brackets are made from stainless steel (polished) rather than steel.

M127-08 Aluminum Hard Top Kit $195.00

M127-09 Fiberglass Hard Top Kit $145.00
Individual pcs.—ask for price.

parts
Notice

MGA Lamp Brackets for optional front driving lamps and (rear) reverse lamp mounting. Fabricated from solid brass (rather than steel), polished and chromed. CSR has been making these for thirty years but once the current supply is sold we will no longer produce. Mounting sundries included.

M46LH & RH—specify. $65.00ea. $125.00 for one pair (LH/RH).
SOLD OUT

new parts
New Items

MGA Factory Aluminum Side Curtain Frame Mounting Brackets Left hand (front & rear) shown for both the early style frame (on left) and Later style frame (on right). Made to original standards from steel and chrome plated (satin finish). Mounting screws available separately or in SC2 Fastener Kit $4.75 (see side curtain details in cat. 11).

SC-12 Early Style—Set of 4 for LH & RH frames. $80.00

SC-13 Later Style—Set of 4 for LH & RH frames. $90.00

SC2-01—Screws for brackets—set of 12 $3.75

Rechroming service available for original brackets $75.00 per set.

new parts
New Items

MGA After Market Aluminum Side Curtain Mounting Brackets Left hand (front & rear) shown. Our brackets are made to replace the weak and somewhat poorly made brackets that came with popular selling frames of the 1960s and ‘70s…Knolls Tool, Amco and others. Made from steel and chrome plated (satin finish) with all fasteners. Extremely strong and adjustable.

SC20-04 (LH & RH set) $80.00

new parts
New Item

MGA Accelerator Stop Bracket (mounts to toeboard)

M155 $15.00ea.  Supplied zinc plated.

Sundry items including spacer, rubber sleeve and fasteners available separately or in kit form—M155-02 (10 pcs.) $4.75

 

new parts
New Item

MGA Clip to secure handbrake cable. M156 $14.00ea.

(BMC No. AHH5295). Supplied zinc plated.

new parts
New Item

Tool for safe and easy removal of distributor drive gear on many BMC engines…MGA, MGB, others. Designed and built by CSR.

SP-31—$9.00ea. Supplied zinc plated.

Catalogue
New Item

Clip for securing flexible fuel lines on MGB, 6 cyl. AH and others.

M37-51—$1.00ea. Steel, zinc plated. BMC Nos. include AEA589 & 12H1001

new parts
New Item

Steel Round Washers in proper/correct dimensions and standards for British cars.
CSR produces hundreds of sizes which are available individually and in sets at discount pricing. Please send us your needs and include dimensions and we will quote availability and prices.

Ref.—Large Washer in photo is used to secure the heat shield material in eng. bay of “big” Healey cars. CSR No. F140 .75ea. up to 15 used per veh.
$10.00 for 15. BMC No. 53K3151. Supplied zinc plated. 

new parts
New Item

MGB Bracket and Clamp Set to secure oil cooler line away from engine.

SP-33 $12.50 for set. (BMC Nos. AHH8300 & AHH6864).
Supplied zinc plated.

new parts
New Items

Assortment of special clips now in production.  Clips shown include breather pipe elongated clip (side of many BMC engines) M37-48 $3.50ea.

Misc. MGA Twin Cam clips including fuel bowl overflow pipe retainer  & grommet which is also used on “big” Healey cars. TC20 (BMC No. AED240) and TC21 (BMC No. 11B424)—$3.00ea. Steel, zinc plated.

CSR makes hundreds of clip sizes all produced to original standards. Available separately and in kit form at discount pricing to service many British vehicles. State your needs and interests.

new parts
New Items

AH100 and Jaguar.  Now in production the proper style Steel loop clips typically used to secure harness sections on BN!, BN2, BN4, Jaguar XK and many other British vehicles.  Please inquire.

M37AH series of clips range in price from .95 to $1.50ea. depending on size and shape. Steel, yellow zinc. Also available in kit form at discount pricing.

M37H (57pcs.) AH BN1/2 cars $62.00

M37I (54pcs.) BN4 (pre Abingdon built cars) $62.00

Kits include all brass and steel loop clips required to secure pipes, cables and harness sections. Plain, clear and yellow zinc plated as original.

new parts
New Items

Half Clips as used on many British vehicles in three “loop” and mounting hole sizes—3/16"(#10), 1/4" and 5/16" in two end leg radii sizes— 5/16" & 5/8". State size and style required .75ea. Steel, zinc plated.

Small clip shown at top is for AH MkI (Bugeye) Sprite—M37-47(H) (BMC No. CHR0405) .80ea. Clips are included in kit form at discount pricing.

M37L—AH Sprite MkI Kit. 32pcs. $25.50.

new parts
New Item

MGA Heater Box Repair Brackets. SP-32. Replacing the rusty and pitted brackets at the base of the box normally helps expedite the restoration of an original box.  Steel, supplied in plain finish.

$20.00 for set of three pcs.

 
new parts
New Items

Hex Screw and large O.D. internal star tooth Lock Washer for sump (oil pan) to engine block. Typical of many British vehicles. 1/4-28 (UNF) Hex Screws in 9/16" length. Available in SS and Steel (plated).

FS005—SS .60ea.

FS005—Steel (Gr.5) .40ea.

FS032—Lock Washer .20ea.

Deduct 10% when purchasing 19 to 25.
Deduct 20% when purchasing 100 to 200.

new parts
New Items

MGA Brackets/Clips to secure brake cable and three way brass junction (not available from CSR).

M156—Clip $14.00ea.

M157—“L” shaped Bracket $3.00ea.

Both pcs. are steel with zinc plating. Hex cap screws and nuts also available from CSR.

new parts

4" Clamps to secure air duct hoses. Two types available. M37-40 Steel, painted black. Used on MGA,  AH 6 cyl. And many other British veh.
$3.75ea.  (BMC No. AHH5714).


New Item

M37-58 Aluminum, plain finish. Used on AH 100 (4). $4.50ea. 

Catalogue
New Item

MGA Trunk Lid Seal. P82 $18.00. Designed and thoroughly tested by CSR. Our sponge core and skinned extruded “D”shaped seal is made in the correct durometer (using new tooling) so shutting and opening the boot lid will not be a chore…and you’ll also obtain a good seal! 

new parts
New Items

MGA Coupé window Brush seals with fasteners and clips—made in stainless. Correct size, shape and style brush seals.

P51-03 Kit services two doors $60.00.

Fiberboard Packing—for weatherstrip finisher on Coupé door. Not pictured.
P51-02 (BMC No.—AFH4569) $5.00 for two.

new parts
New Item

Seat Belt Attachment Brackets for BMC belts typical of the 1950s to mid ‘60s. MGA, AH, plus many other British Vehicles.

M70-04 Tonneau/Wheel Arch end—three point belt. $17.00ea. Can be retrofitted to new three point belts.  With instructions.

M70-06 Two Stud Bracket Plate. Fits to wheel arch—MGA Coupé, “big” Healey, Sprite MkI and others. Includes nuts. $7.50ea.

new parts
New Items

Misc. Metal Loop Clips as used on AH and Jaguar cars.

Large clip on left features a 1-1/4" loop diameter with a hole for 1/4" screw.

Center—brass clips used to secure brake pipes near the rear axle of all “big” Healey cars.

Clip at right holds heater water pipe on 100-4 vehicles. Clips are available individually and in kits. 

new parts
New Items

Jaguar XK Clip/Brackets to hold down wire connection blocks at front of car. (connection blocks not available from CSR) Steel, zinc plated.

M37-55 Wide Clip—$3.50ea.

M37-56 Narrow Clip—$3.50ea.

new parts
New Items

Rubber Extrusions now available. Photo includes end cuts of side curtain rubber, door seals (MGA, MGB, MG-ZA/ZB, Jaguar XK-150 and “big” Healey), BJ7/8 window to top surround rubber, MGA boot lid and battery cover seals.

AH (6 cyl.) and early MGB owners take note—CSR will soon have the correct door seal for your car in production.

new parts
New Items

MGB Brackets (and clips) for securing reverse lamp and overdrive harness to engine and transmission.  Steel, zinc plated. Brackets (at bottom of photo—from left to right)

M170-01 “L” Bracket (BMC No. AHC579) $2.50ea.

M170-02 Bracket with stud (BMC No. 22B512) $4.15ea.

M170-03 “L” Bracket with stud. (BMC No. 22H1303) $3.50ea.
All above (3 items) $9.15—save $1.00

Clips are available in many loop sizes at .85ea. State size required.

new parts
New Items

MGB and others—Elongated double and treble metal loop clips. CSR manufactures a wide range of this style clip which are designed to hold multiple pipes. (3/16", 1/4" and 5/16").

Prices range from $1.50 to $2.00ea. Inquire—state size(s) required and quoting a BMC/BLMC No. is always helpful.

M37-72 Treble Clip (3 – 3/16" pipes).  BMC No. AHC718 $1.75ea.

new parts
New Items

M37M—Metal “Loop” Clip Kit for Magnette ZA/ZB. Kit includes variant style (long leg and end radii) clips as per factory originals. $20.00.

new parts
New Items

Misc. clips with yellow zinc finish and 5/16" leg radii as used on AH100, Jaguar and many other vehicles of the 50s and 60s using this “Lucas” style clip. Available individually and in kits at discount pricing.

Three large clips feature a 7/8" diameter “loop” available In three hole sizes for #10, ¼" and 5/16" screws. 5/16" screw
Factory Nos. include 3H2627 (AH100-4).
CSR No. M37-66 $1.25ea.

Elongated (Double Loop) Clip for up to two 7/16" diameter cables/harness sections with hole for #10 screw.
Factory Nos. include 3H1300 (AH100-4), C-1040/17 (Jaguar).
CSR No. M37-76 $1.50ea.

new parts
New Items

Hex Screw, washer & Nut as used S.U. Carb. Shaft couplings. UNF threaded Stainless Steel fasteners act as a good Replacement for the bent, broken, and difficult to find original BA spec. pcs. Couplings not available from CSR.
CSR No. FS-030-A Screw/Washer/Nut $1.15ea. Set of 6 $6.00
CSR No. FS-030-B 6 pc. Washer Set $1.00

new parts
New Items

Repair Plates with “D” Holes for Cables and Lucas Switches. Produced from .040" steel these plates are designed for easy renewal of worn and destroyed original holes featured on many British vehicle instrument panels. MGA applications noted.
$1.50ea. for .869" O.D. plates and $2.00ea. for 1.125" & 1.369" O.D. plates.
Discounts apply to quantity purchases starting at 5 pcs.

Top, Left to Right
M153-01 Panel Light Switch .869" O.D. / .515" X .562" hole.
M153-02 Main Light Switch 1.125" O.D. / .390" X .437" hole.
M153-03 Turn Signal Switch 1.369" O.D. / .562" X .750" hole.

Bottom, Left to Right
M153-04 Turn Signal Light “Jewel” .869" O.D. / .234" X .343" hole
M153-05 Typical Single Stage Switchs .869" O.D. / .343" X .375" hole
M153-06 Choke/Starter .869" O.D. / .437" X .500" hole
M153-07 Ignition Switch 1.125" O.D. / .725" X .756"

new parts
New Items

M70D—Three Point Mounting Kit for AH MkI Sprite. $84.00.
All pcs. are based on factory designed mountings. Adapter plates (which attach to the double stud plates) for single hole end belt brackets are included. If you are fitting original BMC double hole end (shoulder) belt bracket—see M70-04 in catalogue and “New Parts” listing, kit and price will be adjusted. This comprehensive kit includes tunnel, outside frame and tonneau mounts for two seats.
Pcs. supplied zinc plated.

new parts
New Items

Body Plates now in development. New plates with stamped figures will be made to order. Prototypes shown as a reference. New tooling to make the proper size letter and number fonts is still in production process. Contact us with your interests.
Top: AH MkI Sprite “BAE” Body Plate—Aluminum plate with embossed (raised) figures $25.00ea.
AH MkI Sprite “AN” Body Plate (not shown) Aluminum plate with indented figures $20.00ea.
Bottom: Jaguar. Soft steel plate with embossed (raised) Figures $25.00ea.

new parts
New Items

TC-26 MGA Twin Cam—Clip for securing ignition cables. BMC No. AEH627. Two used Com. (E) 556. Made to original standards and supplied zinc plated. $14.00 ea.